As a prime company in the market, TruXedo has been manufacturing its tonneau covers to fit a wide range of truck models. However, to make the best use of your cover you need to install it properly. Choosing the right model for your vehicle, adjusting it on the bed with the right attachments are some of the key steps to it.
Can You Install a Tonneau Cover With a Bedliner?
It is possible to install a tonneau cover with a bedliner. However, you have to make sure that your cover and bedliner are compatible with each other. All tonneau covers can be installed with all over-the-top bedliners and spray-on or paint-on bedliners.
Bedliners extending over the top of the bed rails blocks the mounting points of the tonneau covers. In this case, you have to cut small notches in the bedliner to attach the clamps. Cut exactly where the tonneau cover clamps attach with the bed rails. Also, it is better to install the liner before you install the cover.
How to Adjust TruXedo Tonneau Cover
The next step after installing the cover is to adjust the tension. It is recommended to adjust and set the tension control at the warmest part of the day. Release hook and loop fastener from both side rail near the cab with the cover closed. After that, check the compression of both spring plungers against the front header.
Spring plungers compensate for material expansion and contraction caused by temperature changes. Roll the cover open and make necessary adjustments. Then re-check the adjustments after closing the cover. Keep doing this until you have achieved satisfactory tension.
Adjusting tension regularly protects your cover against wind wear and ensure the best performance.
How to Install a TruXedo Tonneau Cover
Once you get a TruXedo Tonneau cover that’s compatible with your truck, the installation is pretty simple. The cover components are preassembled. So, it only takes a few minutes.
First of all, take out all the stuff included in the package. There are two side rails, cover assembly, and six clamps provided with the cover. Clamp the side rails under the inside lip of the truck bed with the clamps. Also, keep the tailgate closed to hold the side rails in place while you put the clamps on.
Next, set the cover assembly on the side rails. There is a locator bolt on both sides of the header. They fall into the small holes on the side rails. You’ll find the header guides located on the underside of the front header. Then, slide the header guides onto the side rails.
Then unroll the cover towards the tailgate and press down the rear headers into the header stops. This locks the cover in place. The Truxedo covers are secured using Velcro so there are no snaps. Now, pull the cover fabric to the side rails and secure them using the Velcro fastening system. The cover should be flat and good to go.
How to Install TruXedo Lo Pro on Ram 1500
Like most tonneau covers, the TruXedo Lo Pro tonneau cover does not go over the side rails of your truck. To install it on your Ram 1500, follow these instructions.
Firstly, get the rails and set them on the sides using the clamps. Once the side rails are in place, place the cover header on the rails. Slide the header guides onto the side rails. Lock them in place with the side rails.
Then pull the cover all the way to the tailgate. Press down rear headers into the header stops. Secure the cover using the Velcro on both sides.
Installation of TruXedo Tonneau Cover on Ford f150
Similarly, the installation process is quite simple for the TruXedo tonneau cover on a Ford F-150. Firstly, get the side rails in position. Clamp them to the side rails of your truck using the clamps. Tighten the clamps so that the side rails are secured in their place.
Once the side rails are in position, get the cover and place it over the rails. You’re going to see a locator bolt on each side that folds down and drops into a small hole at the end of the rail. Press the locator bolt in position and slide the header guides in place.
Next, unroll the cover all the way to the tailgate. Once you get to the tail of the rails, you need to drop it down into latches. Then, rotate the rear headers and latch them in place. Also, make sure the Velcro is perfectly attached on both sides.
TruXedo Velcro Replacement Procedure
As sunlight and long-term use can degrade the Velcro, you might have to change the Velcro strips after a few years. You can easily buy TruXedo replacement Velcro strips at the company website.
To replace the Velcro, you need to pull the old Velcro out. The replacement Velcro straps easily slide into the rails. And, there is no adhesive backing.
Besides, there are three drive rivets included in the packaging. You’ll need them in case you are using the TruXedo Edge tonneau cover. However, they are not needed for the TruXedo Lo Pro QT cover.
How Do You Open a TruXedo TruXport Tonneau Cover
Although the TruXport is TruXedo’s entry-level cover, it comes with most of TruXedo ‘s premium features at a cheaper rate. Also, it is quite simple to use.
There are dual latches at the rear end of the TruXport. To open the cover, you need to release the dual latches. Then, all you need to do is just roll the cover to the front to get access to the bed. Make sure to secure the safety straps to hold the cover open.
Frequently Asked Question
Q: Can I lock the TruXedo Lo Pro?
Ans: The TruXedo Lo Pro is latched at the rear which provides the necessary protection. It can not be opened without unlocking and opening the tailgate.
Q: Will the TruXedo Lo Pro work with a 5th wheel?
Ans: To access your fifth wheel, simply open the cover all the way and secure it with the safety straps.
Q: Why is my cover holding water after the rain?
Ans: The TruXedo tonneau covers are not arched. As they are designed to stay flat, some water may sit on the cover.
Conclusion
According to many, TruXedo makes the best tonneau covers. They are easy to install, provide great protection and serve for a long period. Besides, the cover is simple to operate and you can also remove it in seconds!
Leave a Reply