Dodge Challenger enthusiasts know that the ABS & traction control light can be a bit of a mystery. What does it mean? And how do you reset it?
Why dodge challenger ABS and traction control light on? There are several factors, like if you have faulty steering & wheel speed sensor, and your brake fluid level is low then you may face this problem. Also, if there is any malfunction in your ABS & TCS system then your light may stay on.
In this blog post, we will explore why my Dodge Challenger’s ABS and traction control light on and ways to fix it. The article explains the core cause of the issue.

Reasons Why My Dodge Challenger Abs And Traction Control Light On
There are a few reasons your Dodge Challenger may display an ABS or traction control light. Problems with the ABS, the faulty front wheel speed sensors, and the faulty traction control module could be why the ABS and Traction Control warning light is on in your Dodge Challenger.
Sometimes, the light may indicate a problem with the system itself. However, the ABS Traction Control warning light may come on for one or more of below reasons:
Irresponsive Steering Angle Sensor
If your Dodge Challenger is exhibiting problems with its traction or ABS systems, there could be a problem with the steering angle sensor. This sensor helps the car determine the direction it is going, and if it needs to be fixed, the car can’t properly control its movement.
In many cases, fixing this issue involves resetting the sensor. Here are some ways to do just that:
- Turn off the car and wait 10 seconds before starting it again.
- Remove the hood and check for damage to the steering angle sensor. If there is significant damage, you’ll need to replace the sensor. Otherwise, try following step 4.
- Open up the dashboard by removing two screws in the center of the dashboard near where the airbag control module is housed (plastic covers cover these screws).
- Once these covers are removed, you’ll see a connector box on the dashboard and three blue wires coming out of it (two in front and one behind). Disconnect these wires by pulling them out of their connector box (the gray wire will have a red stripe running down its length).
- Resetting the steering angle sensor usually requires connecting one end of a jumper cable directly to one of those blue wires in step 3 and then connecting another end of that cable to either side of an open electrical outlet (preferably one near where you parked your Challenger). Turn on both cars’ headlights so that you have direct.
Problematic Wheel Speed Sensors

Problematic wheel speed sensors are a common issue in cars and trucks. These sensors help to determine the car’s speed by measuring the rotation of the wheels.
If a sensor is not functioning correctly, the car may experience problems with its traction and ABS systems. There are several ways to reset a problematic wheel speed sensor on your Dodge Challenger.
The first step is to check if the sensor is properly installed on the axle. You’ll need to remove the axle and replace the sensor if it isn’t.
Once you’ve confirmed that the sensor is defective, you can reset it using one of three methods: disconnecting and reconnecting wires, programming a computer, or using a tester.
Low Level of Brake Fluid

If your Dodge Challenger has low-level brake fluid, it may cause the ABS and traction control light to come on. There are several ways to reset the Issue:
- Fill up the brake fluid reservoir to the recommended level.
- Reset the ABS by pressing and holding the brake pedal down for three seconds.
- Reset the traction control system by depressing and holding the accelerator pedal down for three seconds.
Blown Circuit Of Anti Brake System
If your Dodge Challenger’s ABS and traction control light are both on, there is a good chance that your brake system has been blown. Several factors can cause this, but the most common cause is a clogged caliper. If you notice any of the following signs that your brakes are starting to fail, it’s time to take action:
- Your car won’t stop when you try to apply the brakes at a standstill.
- The car loses grip when you brake hard.
- The brakes seem to be making loud, strange noises.
How to Reset the ABS and Traction Control Light on a Dodge Challenger

If you are having problems with your Dodge Challenger’s ABS and traction control light coming on, there are a few ways to reset both.
Step 1: First is to determine if the light is coming on due to an issue with the car or a system problem. If it is an issue with the car, you will need to take it to a dealership for service. However, if the light is coming on due to a system problem, you can reset it yourself.
Step 2: Then turn off both the car and the engine.
Step 3: Next, use the keyless remote or the door handle to open the door.
Step 4: After That, press and hold down both of the brake pedal buttons while turning the ignition key all of the way counter-clockwise.
Step 5: Release both brake pedals and turn off the ignition (see image below).
If you’re like me, your Dodge Challenger’s abs and traction control light keep going on and off. Here are a few solutions to resetting these lights; hopefully, they will help.
Leave a Reply